Vue éclatée tondeuse / rasoir électrique Simplicity coronet
Découvrez la vue éclatée complète tondeuse / rasoir électrique Simplicity coronet, un guide indispensable pour identifier facilement toutes les pièces détachées de votre appareil. Que vous soyez à la recherche d'une pièce en particulier ou simplement pour vous aider à la réparation, notre présentation détaillée vous aide à comprendre chaque composant de votre tondeuse / rasoir électrique. Optimisez la maintenance et la réparation de votre appareil grâce à des schémas précis et des références adaptées. Trouvez rapidement les pièces qu'il vous faut pour prolonger la durée de vie de votre tondeuse / rasoir électrique Simplicity coronet et éviter les pannes imprévues.
Assistant réparation
Powered by ChatGPT
Liste des pièces détachées
3 CAPSCREW, Hex Head, 5/16-18 x
Position : 1
1 NUT, Hex, 3/8-16
Position : 1
4 CAPSCREW, Self-Tapping, #10-16 x 3/8
Position : 1
4 CAPSCREW, Self-Tapping, #10-16 x 1/2
Position : 1
1 BELT STOP
Position : 1
21 BOLT, 1/4-20 x 1-3/8
Position : 1
1 * SEAL, Square Cut
Position : 1
1 CABLE, Battery to Ground
Position : 1
1 STEERING WHEEL ASSEMBLY (Includes Ref. No. 49)
Position : 1
2 KEY, Square, 3/16 x 3/16 x 1-1/2 long
Position : 1
1 DECAL, Operating Instructions
Position : 1
1 V-BELT
Position : 1
1 CAP, Spring End
Position : 1
2 NUT, Hex, Flange, 9/16-18
Position : 1
6 CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/2
Position : 2
1 PIVOT
Position : 2
4 WASHER, .34
Position : 2
4 WASHER, 5/16
Position : 2
1 THROTTLE CONTROL ASSEMBLY
Position : 2
1 WASHER, 13/32 x 1 x 1/8
Position : 2
1 CAPSCREW, Hex Head, Whizlock, 5/16-18 x 3/4
Position : 2
1 HOUSING, Lower
Position : 2
1 * RING, Retaining
Position : 2
4 WASHER
Position : 2
2 WASHER, Lock, 1/4
Position : 2
1 ROLL PIN, .188 x
Position : 2
2 REAR WHEEL & TIRE ASSEMBLY, Hoosier, (Includes Ref. Nos. 3, 4, 7 &
Position : 2
1 DECAL,Throttle/Choke
Position : 2
1 DECAL,Throttle/Choke (Red)
Position : 2
1 NUT, Hex Flange, 9/16-18
Position : 2
1 SPRING
Position : 2
4 WASHER, Belleville
Position : 2
1 SHROUD, Rear
Position : 3
1 ARM ASSEMBLY, Lift
Position : 3
8 LOCKWASHER, 5/16
Position : 3
1 CAPSCREW, Hex Head, 1/2-13 x 1-1/4
Position : 3
1 OIL FILTER ELEMENT
Position : 3
5 * WASHER, Thrust
Position : 3
6 COTTER PIN, 3/32 x 3/4
Position : 3
2 NUT, Hex 1/4-20
Position : 3
1 TUBE, Steering
Position : 3
2 REAR WHEEL ASSEMBLY, Metallic Gray
Position : 3
2 DECAL, Icon, Simplicity
Position : 3
1 DECAL, USA (Seat Back)
Position : 3
2 WASHER, Belleville
Position : 3
5 NUT, Hex, ALUM Lock, 3/8
Position : 3
1 PULLEY, 5"
Position : 3
2 WASHER, Flat, 17/64 x 27/32 x 1/8
Position : 3
7 NUT, Hex, Flange, Whizlock, 5/16-18
Position : 4
1 GRIP, Lever
Position : 4
1 GUIDE, Belt, Transmission
Position : 4
1 WASHER, Plain, 17/32 x 1-1/4 x 5/64
Position : 4
1 ROD, Clutch, Rear
Position : 4
1 KLIP RING, 3/4
Position : 4
1 BOOT, Insulator
Position : 4
1 PIN
Position : 4
4 VALVE STEM & CAP
Position : 4
1 DECAL, Seat Deck, LH, (New Style)
Position : 4
1 DECAL, Transmission Release (Hydro models only)
Position : 4
1 PULLEY
Position : 4
1 SPACER
Position : 4
1 HUB, Pulley, 1-35/64"
Position : 4
1 ROD, Deflector
Position : 4
1 SUPPORT, Fuel Tank
Position : 5
1 LEVER, Lift
Position : 5
2 CAPSCREW, Hex Head, Taptite, 5/16-18 x 1/2
Position : 5
1 NUT, Hex, Flange Lock, 5/16-18
Position : 5
2 PIN
Position : 5
1 * COVER, Transaxle
Position : 5
1 ROD, Brake
Position : 5
1 CABLE, Battery to Solenoid (Kohler Models)
Position : 5
1 CABLE, Battery to Solenoid (Briggs & Stratton Models)
Position : 5
3 WASHER, 49/64
Position : 5
14 WASHER, 3/4 (Qty. 10 used on hydro models)
Position : 5
1 DECAL, Seat Deck, RH, (New Style)
Position : 5
1 DECAL, Belt & Blade Replacement
Position : 5
1 HUB, Pulley, 1-3/16
Position : 5
1 ROD, Adjustment
Position : 5
2 COVER, Arbor Housing ASSEMBLY
Position : 5
1 ARM ASSEMBLY
Position : 5
3 JAMNUT, Hex, 1/2-13
Position : 5
1 CARRIAGE BOLT, 5/16-18 x 3/4
Position : 6
1 SPRING, Compression
Position : 6
1 DUCT, R.H., Top
Position : 6
1 DUCT, R.H., Top
Position : 6
1 AIR DUCT
Position : 6
1 SPACER
Position : 6
1 NUT, Hex, Flange Lock, 1/2 x
Position : 6
1 SHAFT, Motor
Position : 6
1 SPRING, Compression
Position : 6
1 TUBE
Position : 6
1 TUBE, Vent (Early Models Only)
Position : 6
2 BUSHING
Position : 6
A/R SPACER (Hydro models only)
Position : 6
1 DECAL, Touch-up Paint, Deep Orange & Charcoal Gray
Position : 6
6 CAPSCREW, Hex Head, Taptite, 5/16-18 x
Position : 6
4 BEARING
Position : 6
2 CARRIAGE BOLT, 5/16-18 x 1-1/4
Position : 6
1 STRAP, Fuel Tank, Brace
Position : 7
3 WASHER, Plain, 13/32 x 7/8 x 5/64
Position : 7
1 CAPSCREW, 5/16-18 x 3/4
Position : 7
1 VALVE, Shut Off
Position : 7
4 WASHER, Plain, 5/16
Position : 7
2 NUT, Hex, Flange Lock, 1/2 x
Position : 7
2 NUT, Hex, Flange Whizlock, 5/16-18
Position : 7
2 WASHER
Position : 7
1 * GASKET ELIMINATOR (Loctite #515)
Position : 7
1 WASHER, 5/16 x 1-1/4 x 1/16
Position : 7
6 COTTER PIN, 7/64 x 3/4
Position : 7
1 BATTERY
Position : 7
1 TUBE ASSEMBLY, Shift
Position : 7
2 TIRE, Rear Wheel, 16 X 6.50-8
Position : 7
1 DECAL, "CORONET"
Position : 7
1 DECAL, Danger, Rotating Cutting Blade
Position : 7
1 ADAPTER, Arbor
Position : 7
2 SPACER
Position : 7
1 CAP, Fuel Tank, Vented
Position : 8
3 COTTER PIN, 3/32 x 3/4
Position : 8
1 SEAL, Air Inlet
Position : 8
4 WASHER, 5/16
Position : 8
6 LOCKWASHER, 5/16
Position : 8
2 CARRIAGE BOLT, 5/16-18 x 5/8
Position : 8
1 RING, Retaining
Position : 8
2 NUT, Hex, Nylon Lock, 5/16-18
Position : 8
1 WASHER, Lock, External Tooth, 5/16
Position : 8
1 WASHER
Position : 8
2 TUBE, Rear Wheel
Position : 8
1 DECAL, Model, Coronet, 11 - 5 Speed
Position : 8
1 DECAL, Model, Coronet, 14 - Hydro
Position : 8
1 DECAL, Model, Coronet, 10.5 - Hydro
Position : 8
1 DECAL, Model, Coronet, 13 - Hydro
Position : 8
1 DECAL, 16 HP
Position : 8
1 GASKET, Foam
Position : 8
2 WASHER
Position : 8
2 GASKET, Foam
Position : 8
1 ROD, Adustment
Position : 8
1 TANK, Fuel
Position : 9
1 CABLE ASSEMBLY, Lift
Position : 9
3 NUT, Flange, Whizlock, 5/16-18
Position : 9
5 LOCKWASHER, 5/16
Position : 9
2 CAPSCREW, Hex, M08 - 1.25 x 30mm
Position : 9
1 CARRIER ASSEMBLY
Position : 9
1 CARRIAGE BOLT, 5/16-18 x 5/8
Position : 9
1 SEAL, Lip .26 x .42 x .8
Position : 9
1 * SHAFT, Input (3-5/16" Long)
Position : 9
2 WASHER
Position : 9
1 STRAP, Battery
Position : 9
2 BUSHING
Position : 9
2 RETAINER, Hub Cap
Position : 9
2 DECAL, Simplicity
Position : 9
1 DECAL, Cutting Width - 34", Black, Blue & Gray
Position : 9
1 DECAL, Cutting Width - 34", Silver on Black
Position : 9
1 ARBOR HOUSING ASSEMBLY (Incl. Ref. No. 10)
Position : 9
2 NUT, Hex, 1/4-20
Position : 9
2 ARBOR HOUSING ASSEMBLY, (Includes Ref. No. 10)
Position : 9
2 CLIP, Hair Pin
Position : 9
2 CARRIAGE BOLT, 1/4-20 X 7/8
Position : 9
1 SPACER, 21/64 x 1/2 x 21/64
Position : 10
1 NUT, Hex, Esna Lock, 3/8-16
Position : 10
1 VALVE, Shut-Off
Position : 10
2 CAPSCREW, Hex, #8 - 1.25 x 30mm
Position : 10
1 STRAP, Torque
Position : 10
1 CAPSCREW, Hex, 5/16-18 x 2-1/4
Position : 10
1 BRAKE ROTOR/STATOR KIT
Position : 10
1 * "O" RING
Position : 10
1 ROD, Shift, Front
Position : 10
2 CAPSCREW, Metric, M08-1.25 x 20 mm
Position : 10
1 WASHER, Plain, 17/32 x 1-1/4 x 7/64
Position : 10
2 WASHER, 3/4 I.D. x 1-1/16 O.D. x 1/16 Thk.
Position : 10
1 DECAL, Briggs & Stratton, 11 HP
Position : 10
1 DECAL, Briggs & Stratton, 13 HP, INTEK
Position : 10
1 DECAL, Briggs & Stratton, 10.5 HP
Position : 10
1 DECAL, Briggs & Stratton, 13 HP
Position : 10
1 DECAL, Kohler, 14 HP
Position : 10
1 DECAL, Kohler, 16 HP
Position : 10
1 DECAL, Danger, Chute In Place
Position : 10
1 FITTING, Grease
Position : 10
2 LOCKWASHER, 1/4
Position : 10
2 FITTING, Grease
Position : 10
1 HOUSING ASSEMBLY, 34" (Orange)
Position : 10
1 WASHER, Plain, 13/32 x 7/8 x 5/64
Position : 11
1 PULLEY, Lift
Position : 11
2 WASHER, Plain
Position : 11
1 WASHER, 5/16
Position : 11
1 CAPSCREW, Taptite, #10-24 x 1-1/4
Position : 11
1 BOLT, 5/16-18 x 1-3/4
Position : 11
1 * BEVEL PINION, Input
Position : 11
1 CARRIAGE BOLT, 5/16-18 X 1-1/4
Position : 11
1 ROD, Clutch, Rear
Position : 11
1 BRACE, Battery
Position : 11
1 SPRING, Torsion
Position : 11
2 E RING
Position : 11
2 DECAL, Logo, AGCO
Position : 11
1 DECAL, Cutting Width - 30", Black, Blue & Gray
Position : 11
1 DECAL, Cutting Width - 30", Silver on Black
Position : 11
2 BEARING
Position : 11
1 ARM ASSEMBLY, Mower
Position : 11
2 WASHER
Position : 11
2 SPACER, Roller
Position : 11
2 CAPSCREW, Hex Head, 3/8-16 x 1-1/4
Position : 11
3 CAPSCREW, Taptite, 5/16-18 x 1-1/ (14 & 16HP Models)
Position : 12
3 CAPSCREW, Hex, Taptite, 5/16-18 x 1 (11 & 13 HP Models)
Position : 12
1 SPACER
Position : 12
2 BELT STOP, (Hydro Models)
Position : 12
1 BELT STOP, Rear (Gear Models)
Position : 12
2 BELT STOP
Position : 12
2 CAPSCREW, Hex Head, M08 - 1.25 x 40mm
Position : 12
1 CAPSCREW, Hex, Whizlock, 5/16-18 x 3/4
Position : 12
1 WASHER, 1/4
Position : 12
1 NUT, Hex, Lock, 5/16-24
Position : 12
1 * RING, Retaining
Position : 12
2 SPACER
Position : 12
1 ROD, Brake
Position : 12
2 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position : 12
2 COTTER PIN
Position : 12
2 CAP, Threaded
Position : 12
1 DECAL, Seat Deck Stripe, LH (411G)
Position : 12
1 DECAL, Seat Deck Stripe, LH (414H)
Position : 12
1 DECAL, Seat Deck AGCO, LH
Position : 12
1 DECAL, Free Floating Mower
Position : 12
1 SPACER
Position : 12
3 JAMNUT, Hex, 3/8-16
Position : 12
1 SPRING
Position : 12
5 WASHER, Flat, 5/8
Position : 12
3 WASHER, Flat, 3/8
Position : 12
1 BUSHING, Rubber
Position : 13
1 WASHER, Plain, 13/32 x 1-1/2 x 1/8
Position : 13
1 BELT STOP, Front (Gear Models)
Position : 13
1 CLUTCH, Electric
Position : 13
1 WASHER, 7/16
Position : 13
1 SPRING
Position : 13
1 COMPRESSION SPRING
Position : 13
1 * WASHER, Thrust
Position : 13
3 WASHER, 5/16
Position : 13
2 WASHER
Position : 13
1 ROD, Shift
Position : 13
2 HUB CAP, Scalloped, 8"
Position : 13
1 DECAL, Seat Deck Stripe, RH (411G)
Position : 13
1 DECAL, Seat Deck Stripe, RH (414H)
Position : 13
1 DECAL, Seat Deck AGCO, RH
Position : 13
1 COVER, Arbor Housing
Position : 13
1 SPACER
Position : 13
1 CAPSCREW, 3/8-16 x 2-1/2
Position : 13
7 ROLLER
Position : 13
1 ELBOW
Position : 14
1 CAPSCREW, Hex Head, 3/8-16 x 1-1/2
Position : 14
2 WASHER, 3/8
Position : 14
1 CAPSCREW, Hex, 7/16-20 x 2-1/2
Position : 14
2 CAPSCREW, Hex Head, Taptite, 3/8-18 x 1-1/4
Position : 14
1 WASHER, Plain, 13/32 x 1-1/4 x 1/16
Position : 14
2 PIN, Actuating
Position : 14
1 * GEAR, Spur (16 Teeth)
Position : 14
1 BAR, Shift, Rear
Position : 14
1 WASHER, 13/32 x 1-1/4 x 5/64
Position : 14
1 WASHER, Lock, External Tooth, 3/8
Position : 14
1 KNOB, Rod, Shift
Position : 14
2 FRONT WHEEL & TIRE ASSEMBLY, Hoosier, 13 x 5.00-6, Metallic Gray
Position : 14
2 DECAL, Model,
Position : 14
2 DECAL, Model, 413H
Position : 14
2 DECAL, Model,
Position : 14
1 WASHER, Cupped
Position : 14
1 TRUNNION
Position : 14
2 WASHER, Flat, 3/8
Position : 14
1 SHAFT ASSEMBLY, Roller (Includes Ref. 20)
Position : 14
2 CLAMP, Hose
Position : 15
1 NUT, Hex, Flange Lock, 3/8-16
Position : 15
1 CAPSCREW, Taptite, 3/8-16 x
Position : 15
3 NUT, Hex, Flange, Whizlock, 5/16-18
Position : 15
1 LEVER, Release
Position : 15
1 ARM, Actuating
Position : 15
1 * COUNTERSHAFT, (4-7/8" Long)
Position : 15
1 CARRIAGE BOLT, 5/16-18 x
Position : 15
2 NUT, Hex, Lock, 5/16-18
Position : 15
1 NUT, Hex, 3/8-16
Position : 15
1 WASHER, Plain, 11/32 x 1 x 1/8
Position : 15
2 FRONT WHEEL ASSEMBLY 13 x 5.00-6, Metallic Gray (Includes Ref. No.
Position : 15
1 DECAL, Touch-up Pain, Red & Gray
Position : 15
1 SHAFT, Arbor, 5-53/64"
Position : 15
2 PIN, Locking
Position : 15
1 PULLEY, Idler, Backside
Position : 15
1 HOSE, Fuel Line
Position : 16
1 ECCENTRIC
Position : 16
1 PUSH NUT, 5/16-18
Position : 16
1 PIPE, Exhaust
Position : 16
1 STRAP, Torque
Position : 16
1 SPACER
Position : 16
3 WASHER, 7/16 x 7/8 x 1/16
Position : 16
1 * GEAR, Spur (15 Teeth)
Position : 16
1 CAPSCREW, Hex Head, 1/4-28 x 5/8
Position : 16
1 WIRE ASSEMBLY, Harness to Engine (Briggs & Stratton Only)
Position : 16
1 SHAFT ASSEMBLY, Steering
Position : 16
4 BUSHING, Metal, 7-21/32 I.D.
Position : 16
2 DECAL, Logo, Massey Ferguson
Position : 16
1 SHIELD, Grass, Lower
Position : 16
2 CARRIAGE BOLT, 3/8-16 x 1-1/2
Position : 16
1 SPACER
Position : 16
1 PLATE, Support, RH
Position : 16
1 FILTER, Fuel
Position : 17
1 WASHER, 13/32 x 7/8 x 1/8
Position : 17
1 CAPSCREW, Hex, Whizlock, Flange, 5/16-18 x 1-1/2
Position : 17
1 NUT, Hex, Lock, 1/4-20
Position : 17
1 CASTLE NUT, 5/16-24
Position : 17
1 * GEAR, Spur (23 Teeth)
Position : 17
1 LOCKWASHER, 1/4
Position : 17
1 WASHER, Plain
Position : 17
2 CLAMP, Wire (11 HP B&S 5-Speed Only)
Position : 17
1 WASHER, Plain
Position : 17
2 Grease Fitting
Position : 17
1 DECAL, Seat Deck Stripe, LH (2413H)
Position : 17
1 DECAL, Seat Deck Stripe, LH (2411G)
Position : 17
1 DECAL, Seat Deck Stripe, LH (2414H)
Position : 17
1 DECAL, Seat Deck, LH, (New Style)
Position : 17
1 BLADE, Mower, 30"
Position : 17
2 PIN, Retaining
Position : 17
2 NUT, Hex Alum Lock, 3/8
Position : 17
3 NUT, Hex Lock, Alm Insert, 3/8-16
Position : 17
2 PUSH NUT, 5/16
Position : 18
1 CAPSCREW, Hex Head, 3/8-16 x 1-3/4
Position : 18
1 ** KEY (All Models)
Position : 18
1 ** KEY
Position : 18
1 SPRING, Return
Position : 18
1 STRAP, Torque
Position : 18
1 COTTER PIN
Position : 18
1 WASHER, Plain, 17/64 x 5/8 x 3/64
Position : 18
1 CARRIAGE BOLT, 5/15-18 x 2-3/4
Position : 18
1 GROMMET (11 HP 5-Speed Models Only)
Position : 18
2 CARRIAGE BOLT, 3/8-16 x
Position : 18
2 TIRE, Front Wheel, 13 x 5.00-6
Position : 18
1 DECAL, Seat Deck Stripe, RH (2413H)
Position : 18
1 DECAL, Seat Deck Stripe, RH (2411G)
Position : 18
1 DECAL, Seat Deck Stripe, RH (2414H)
Position : 18
1 DECAL, Seat Deck, RH, (New Style)
Position : 18
1 WASHER, Hex
Position : 18
2 CARRIAGE BOLT, 5/15-18 x 1-1/4
Position : 18
1 NUT, Hex, 3/8-16
Position : 18
2 BOLT, Shoulder, 3/8-16
Position : 18
10 CAPSCREW, Hex Head, Whizlock, 5/16-18 x 3/4
Position : 19
1 SPINDLE ASSEMBLY, LH
Position : 19
1 PULLEY, Engine (Gear Models)
Position : 19
1 PULLEY, Engine (Hydro Models)
Position : 19
1 PULLEY, Engine
Position : 19
4 CAPSCREW, Hex Head, 5/16-18 x 2-1/4
Position : 19
2 WASHER, 5/16
Position : 19
1 BRACKET, Shift
Position : 19
1 SWITCH, Neutral Start
Position : 19
1 PLATE, Steering Mounting
Position : 19
2 TUBE, Front Wheel, 4.10/3.50 x
Position : 19
2 DECAL, Model,
Position : 19
2 DECAL, Model,
Position : 19
2 DECAL, Model,
Position : 19
1 WASHER, Spring
Position : 19
2 SPACER
Position : 19
1 NUT, Hex, Flange, Lock, 3/8-16
Position : 19
2 WASHER, Flat, 1/2
Position : 19
1 PAD, Foot Rest, LH
Position : 20
3 NUT, Hex, Flange Lock, 5/16-18
Position : 20
1 SLEEVE, Clutch Anchor
Position : 20
1 NUT, Speed, 5/16-18
Position : 20
2 NUT, Hex, Flange Lock, 5/16-18
Position : 20
1 ACTUATOR, Bypass
Position : 20
2 LOCKWASHER, 5/16
Position : 20
2 POP-RIVET
Position : 20
2 NUT, Hex, 3/8-16
Position : 20
2 KLIP RING
Position : 20
1 CAPSCREW, Hex Head, 7/16-14 x 1, GR
Position : 20
1 CLAMP
Position : 20
1 CAPSCREW, Hex Head, 3/8-16 x 2-3/4
Position : 20
2 NUT, Push
Position : 20
1 PUSHNUT
Position : 20
1 FRAME ASSEMBLY (Includes Ref. No. 2)
Position : 21
2 SPACER
Position : 21
1 CLUTCH, Electric, Kit
Position : 21
1 NUT, Speed, Lug Type, 5/16-18
Position : 21
1 KEY, Woodruff, #9
Position : 21
1 CAPSCREW, Hex, Whizlock, 5/16-18 x 1-1/2
Position : 21
1 BYPASS PLATE
Position : 21
1 * GEAR, Spur (34 Teeth)
Position : 21
4 CAPSCREW Taptite, 5/16-18 x 1/2
Position : 21
1 WIRE ASSEMBLY, Neutral Switch (11 HP Coronet Only)
Position : 21
1 CAPSCREW, Hex Head, 5/16-18 x 1-1/2
Position : 21
2 CAP, Threaded
Position : 21
1 CAPSCREW, Hex Head, 3/8-16 x
Position : 21
3 WASHER, Plain (1 Required for Export)
Position : 21
1 SPACER
Position : 21
2 NUT, Flange Lock, 3/8
Position : 21
1 PAD, Foot Rest, RH
Position : 22
2 KLIP RING
Position : 22
1 CAPSCREW, Hex Head, 7/16-20 x 2-1/2
Position : 22
1 RING, Retaining
Position : 22
1 * TRANSMISSION, Hydro (HydroGear, Mod 311-0500)
Position : 22
1 BLOCK, Cylinder (Motor) Assembly
Position : 22
1 * WASHER, Thrust
Position : 22
1 KLIPRING, 1/2
Position : 22
2 NUT, Hex Flange Lock, 5/16-18
Position : 22
2 TIE, Self-Locking
Position : 22
1 NUT, Hex, Flange Lock, 3/8-16
Position : 22
2 HUB CAP, 6", Scalloped
Position : 22
2 WASHER, Flat, 3/8 x 1-1/2 x 1/8
Position : 22
2 SPACER (Export)
Position : 22
5 CAPSCREW, Taptite, 5/16-18 x 5/8
Position : 22
1 WASHER
Position : 22
14 FASTENER
Position : 23
2 CARRIAGE BOLT, 5/16-18 x
Position : 23
1 LOCKWASHER, 7/16
Position : 23
1 SUPPORT, Muffler
Position : 23
3 CAPSCREW, Hex, Taptite, 5/16-18 x 1/2
Position : 23
1 PULLEY ASSEMBLY, Driven, Transmission
Position : 23
1 BEARING, Thrust .42 x .68 x .16
Position : 23
1 * IDLER ASSEMBLY Reverse
Position : 23
2 WASHER, Plain, 1/2
Position : 23
3 LOCKWASHER, 5/16
Position : 23
1 SOLENOID
Position : 23
3 WASHER, 13/32 x 1-1/2 x 1/8
Position : 23
4 HUB CAP, Silver
Position : 23
1 SPRING
Position : 23
2 PUSHNUT, 1/4
Position : 23
1 LEVER ASSEMBLY
Position : 23
1 COVER, Arbor
Position : 23
1 SPRING
Position : 23
1 PANEL, Front
Position : 24
1 TIE ROD, LH
Position : 24
2 CAPSCREW, Taptite, 3/8-16 x 1-1/2
Position : 24
3 CAPSCREW, Hex Head, Taptite, 5/16-18 x 1/2
Position : 24
1 AIR DUCT, Bottom
Position : 24
1 V-BELT
Position : 24
4 CAPSCREW, Taptite, 5/16-18 x 2-1/4
Position : 24
1 CENTER SECTION ASSEMBLY
Position : 24
1 * SEAL, Square Cut
Position : 24
1 CARRIAGE BOLT, 5/16-18 x 2-3/4
Position : 24
2 CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/2
Position : 24
1 GEAR, Steering
Position : 24
1 SPACER
Position : 24
6 WASHER, Flat, 3/8
Position : 24
2 WASHER, Flat, 3/8
Position : 24
1 PLATE, Support
Position : 24
4 PAL NUT, 5/16-18
Position : 25
1 WASHER
Position : 25
1 GASKET, Muffler
Position : 25
1 AIR DUCT, Bottom
Position : 25
1 SHIELD, Muffler
Position : 25
1 PULLEY ASSEMBLY, Drive, Engine
Position : 25
1 V-BELT
Position : 25
2 SEAL, Wiper
Position : 25
1 * BUSHING
Position : 25
1 TORSION BAR
Position : 25
1 SPACER
Position : 25
1 CIRCUIT BREAKER
Position : 25
1 SPACER
Position : 25
1 LEVER ASSEMBLY
Position : 25
2 PLATE, Pivot Support
Position : 25
1 V-BELT
Position : 25
1 SUPPORT, "U" Seat (14 & 16 HP Models)
Position : 26
1 SUPPORT, "U", Seat (11 & 13 HP Models)
Position : 26
1 SPACER, 21/64 x 1/2 x 5/8
Position : 26
1 PIPE, Exhaust
Position : 26
1 PIPE, Exhaust
Position : 26
1 SHIELD, Muffler
Position : 26
5 CAPSCREW, Hex, Thd. Form, #10-16 x 3/8
Position : 26
1 BELT STOP
Position : 26
2 SLEEVE BEARING
Position : 26
2 * WASHER, Thrust
Position : 26
2 BRACKET, Torsion Bar
Position : 26
1 ROD, Control
Position : 26
1 WIRE ASSEMBLY
Position : 26
1 CAPSCREW, Hex Head, 3/8-16 x
Position : 26
2 WASHER, Plain, 3/8
Position : 26
1 HOUSING ASSEMBLY, 30" (Orange)
Position : 26
1 PULLEY, 3-3/4"
Position : 26
2 BUMPER, Rubber
Position : 27
2 WASHER
Position : 27
2 CAPSCREW, Socket Head, 5/16-18 x 3/4
Position : 27
4 CAPSCREW, Hex Head, Thd. Form, #10-16 x 3/8
Position : 27
1 SLEEVE, Anchor, Clutch
Position : 27
1 BELT STOP
Position : 27
2 SEAL, 3/4 x 1-1/4 x 1/4
Position : 27
1 * GEAR, Spur (11 Teeth)
Position : 27
4 CAPSCREW, Hex Head, Flange, Taptite, 5/16-18 x 1/2
Position : 27
1 ROD, Shift, Front
Position : 27
1 LOCKWASHER, 5/16
Position : 27
1 DASH, Hydro
Position : 27
1 PULLEY ASSEMBLY Idler, Fixed, 6" Dia.
Position : 27
2 BOLT, Shoulder
Position : 27
1 HUB, Pulley, 1-3/16"
Position : 27
1 CAPSCREW, Hex Head, Taptite, 5/16 x 1/2
Position : 28
1 LEVER
Position : 28
1 CARRIAGE BOLT, 5/16-18 x 3-1/4
Position : 28
1 WASHER
Position : 28
2 WASHER, 3/4 x 1.5 x .13
Position : 28
1 * BEARING, Needle
Position : 28
1 SPACER, Pivot
Position : 28
2 WASHER, Plain, 1/2 x 1 x 1/32
Position : 28
3 COVER, Terminal
Position : 28
1 DASH, Gear
Position : 28
1 NUT, Hex, Whizlock, 3/8-16
Position : 28
2 WASHER, Flat
Position : 28
1 DUCT, Air Inlet (11 & 13 HP Models)
Position : 29
1 DUCT, Air Inlet (14 & 16 HP Models)
Position : 29
1 ROD, Hitch
Position : 29
1 CLAMP, Muffler
Position : 29
1 SWITCH
Position : 29
1 PULLEY, Transmission
Position : 29
1 DIFFERENTIAL ASSEMBLY
Position : 29
2 CLEVIS, Idler, Bracket
Position : 29
2 NUT, Hex, 5/16-24
Position : 29
3 CAPSCREW, Hex, Flange, Taptite, 1/4-20 x 3/4
Position : 29
1 GRIP, Lever
Position : 29
2 SUPPORT ASSEMBLY, Roller
Position : 29
2 SHIELD, Grass, Lower
Position : 29
2 SPACER, Plastic
Position : 30
2 CAPSCREW, Hex Head, 1/2-13 x 1-1/2
Position : 30
1 SPACER
Position : 30
2 CAPSCREW, Hex Head, 1/4-20 x 7/8
Position : 30
2 BELT STOP (Hydro Models)
Position : 30
1 COVER, Terminal
Position : 30
1 LOCKWASHER, 1/2
Position : 30
1 BLOCK, Cylinder Pump Assembly
Position : 30
1 * WASHER, Thrust
Position : 30
1 SPRING, Idler
Position : 30
1 ROD, Return, Front
Position : 30
1 CABLE, Solenoid to Starter
Position : 30
1 KNOB, Rod, Parking Brake
Position : 30
2 NUT, Hex, Flange, Whizlock, 3/8-16
Position : 30
1 BLADE, 14-27/64"
Position : 30
2 SPACER
Position : 31
1 HITCH, Hook
Position : 31
1 SUPPORT, Muffler
Position : 31
1 SUPPORT, Muffler
Position : 31
1 PIN, Cotter 1/8 x 1-1/2
Position : 31
1 NUT, Hex, Jam, 1/2-20
Position : 31
1 SPRING, Block
Position : 31
1 * GEAR, Spur (19 Teeth)
Position : 31
2 CAPSCREW, Hex Head, Flange, Taptite, 1/4-20 x 5/8
Position : 31
1 CARRIAGE BOLT, 1/4-20 x 7/8
Position : 31
2 (1) CLIP (14 HP Hydro Qty=1)
Position : 31
1 ROD, Parking Brake
Position : 31
3 WASHER, 13/32 x 1 x 1/8
Position : 31
2 NUT, Adjustment
Position : 31
2 WASHER, Hex
Position : 31
2 PIN, Quick
Position : 32
2 SPACER
Position : 32
1 SPEED NUT, 5/16-18
Position : 32
1 NUT, Hex Head, 1/2 x
Position : 32
1 COTTER PIN, 1/8 x 1-1/2
Position : 32
1 WASHER, Block Thrust
Position : 32
3 * WASHER, Thrust
Position : 32
1 LEVER, Idler, Pulley
Position : 32
1 LEVER, Control
Position : 32
1 IDLER PULLEY, Backside
Position : 32
4 WASHER, Plain, 21/32 x 1-1/8 x 7/64
Position : 32
2 WASHER, Spring
Position : 32
2 PIVOT, Hood
Position : 33
2 NUT, Hex, Flange Lock, 1/2-13
Position : 33
1 MUFFLER ASSEMBLY
Position : 33
2 WASHER, Belleville 1/2
Position : 33
2 WASHER, Belleville, 1/2
Position : 33
1 SHAFT, Input
Position : 33
1 PULLEY, Idler
Position : 33
2 CARRIAGE BOLT, 5/16-18 X 1-1/4
Position : 33
1 WASHER, Internal Tooth, 5/8
Position : 33
2 NUT, Hex, Flange, Whizlock, 5/16-18
Position : 33
1 LOCKWASHER, 3/8
Position : 33
2 ROLLER
Position : 33
2 CAPSCREW, Hex Head, 7/16-14 x 1-1/4, GR
Position : 33
2 FITTING, Lube
Position : 34
1 SPINDLE ASSEMBLY, RH
Position : 34
1 DUCT, L.H.
Position : 34
1 DUCT, L.H.
Position : 34
1 PULLEY
Position : 34
1 SPACER
Position : 34
1 NUT, Hex Lock, 5/16-24
Position : 34
1 * GEAR, Spur (27 Teeth)
Position : 34
3 NUT, Hex, Flange Whizlock, 1/4-20
Position : 34
1 NUT
Position : 34
1 QUADRANT, Lift
Position : 34
1 NUT, Hex, 3/8
Position : 34
2 WASHER, 21/32 x 1-1/8 x 1/16
Position : 34
12 CAPSCREW Taptite, 5/16-18 x 3/4
Position : 34
4 WASHER
Position : 35
1 TIE ROD, RH
Position : 35
1 KNOB, Throttle
Position : 35
1 CAPSCREW, Hex Head, 5/16-18 x
Position : 35
1 CAPSCREW, Hex Head, With Hole, 1/2-20 x 1-3/4
Position : 35
1 SPACER
Position : 35
1 * GEAR, Spur (35 Teeth)
Position : 35
1 TUBE, Plastic
Position : 35
1 ROD, Return, Rear
Position : 35
1 COVER, Keyswitch
Position : 35
3 CAPSCREW, Hex Head, Taptite, 1/4-20 x 1/2
Position : 35
1 NUT, Hex, Lock, 3/8-16
Position : 35
2 RING, Retaining
Position : 35
1 NUT, Hex, 3/8-16
Position : 35
2 CAPSCREW, Hex Head, 5/16-18 x 1-1/2
Position : 36
1 THROTTLE CONTROL ASSEMBLY
Position : 36
2 CAPSCREW, Hex Head, 1/2-13 x 1-1/4
Position : 36
1 NUT, Hex, Slotted, 1/2-20
Position : 36
1 SPRING
Position : 36
1 * SPACER, Neutral
Position : 36
1 KLIP RING, 3/8
Position : 36
1 CAPSCREW, 5/16-18 x 1-3/4
Position : 36
1 KEYS (Set of 2 Keys)
Position : 36
2 CLAMP
Position : 36
4 CAPSCREW, Taptite, 5/16-18 x 3/4
Position : 36
1 SHAFT, Arbor, 6-33/64"
Position : 36
2 NUT, Hex, 5/16-18
Position : 37
2 SCREW, Plastite, 1/4-10 x 1/2
Position : 37
1 WASHER
Position : 37
2 PUCK, Dampener
Position : 37
1 * GEAR, Spur (22 Teeth)
Position : 37
1 PIVOT, Brake
Position : 37
1 SPACER
Position : 37
1 SWITCH, Seat
Position : 37
2 WASHER, Plain, 1/4
Position : 37
2 BAR, Mower Transport
Position : 37
1 BLADE, 19-29/32"
Position : 37
2 CAPSCREW, 5/16-18 x 1-1/4
Position : 38
1 STOP, Throttle (Not Pictured, Export Models Only)
Position : 38
1 ARM, Control
Position : 38
3 * WASHER
Position : 38
1 ROD, Clutch, Front
Position : 38
1 CAPSCREW, Hex Head, 1/4-20 x 3/4
Position : 38
1 * SWITCH, PTO, Electric Clutch
Position : 38
2 CAPSCREW, Hex Head, 1/4-20 x 7/8
Position : 38
2 CAPSCREW, Hex, 3/8-16 x 1-14
Position : 38
1 SPACER
Position : 39
1 SEAL, Lip
Position : 39
1 PIVOT SHAFT ASSEMBLY
Position : 39
1 WIRE ASSEMBLY, Clutch
Position : 39
1 NUT, Hex, Flange Centerlock, 1/4-20
Position : 39
2 SPACER
Position : 39
2 WASHER, 1"
Position : 40
1 TIE, Self Locking
Position : 40
1 STUD, 5/16-24
Position : 40
1 * SHAFT, Brake (4 Keyed)
Position : 40
1 LEVER, Clutch
Position : 40
2 CLEVIS, Idler Bracket
Position : 40
1 HARNESS, Wiring
Position : 40
3 SPACER, 17/64 x 3/8 x 21/64
Position : 40
1 ROD, Latch, Hitch
Position : 40
1 CAP, Black, Vinyl
Position : 41
1 SET SCREW
Position : 41
4 * SHIFT KEY
Position : 41
1 PAD, Pedal
Position : 41
1 CAPSCREW, Taptite, 1/4-20 x 5/8
Position : 41
1 IGNITION KEY SWITCH ASSEMBLY
Position : 41
6 CAPSCREW, Hex Head, Whizlock, 5/16-18 x 3/4
Position : 41
1 HITCH ASSEMBLY
Position : 41
1 ADJUSTER, Seat
Position : 42
1 * COLLAR, Shifter
Position : 42
1 WASHER
Position : 42
1 SUPPORT, Steering
Position : 42
1 CAPSCREW, Hex Head, 3/8-16 x
Position : 42
1 SPRING, Extension
Position : 43
1 BEARING, Shaft Ball
Position : 43
1 * SPRING
Position : 43
1 NUT, Hex, 5/16-18
Position : 43
1 SHROUD, Front (Orange)
Position : 43
1 SPRING
Position : 43
1 SUPPORT, Seat
Position : 44
1 RING, Wire, Retaining
Position : 44
1 * BALL, Steel
Position : 44
1 PLATE
Position : 44
2 CARRIAGE BOLT, 1/4-20 x 3/4
Position : 44
4 SPACER
Position : 45
1 RING, Retaining
Position : 45
1 * ROD & FORK ASSEMBLY, Shift
Position : 45
1 SPRING
Position : 45
1 ROD, Lift Height
Position : 45
2 CARRIAGE BOLT, 1/4-20 x 1-1/4 (Export)
Position : 45
1 SEAT ASSEMBLY
Position : 46
1 SEAL, Lip
Position : 46
2 * SEAL RING
Position : 46
1 NUT, Hex, Jam, Lock, 3/8-16
Position : 46
2 NUT, Hex, Jam, 1/4-20
Position : 46
1 ROD, Deflector
Position : 46
1 DECK, Seat, Orange
Position : 47
1 DECK, Seat, Red
Position : 47
1 SEAL, Lip, 1.0 x .25 x .7
Position : 47
1 * AXLE, (16-13/16" Long)
Position : 47
1 KNOB, Rod, Lift Height
Position : 47
1 DEFLECTOR, Plastic
Position : 47
3 RIVET
Position : 48
1 RING, Retaining
Position : 48
2 * WASHER
Position : 48
1 GUARD, Spring
Position : 48
2 NUT, Hex, Flange, Whizlock, 1/4-20
Position : 48
1 SCREEN, Seat Deck Top
Position : 49
1 ARM, Bypass
Position : 49
2 * GEAR, Bevel, 13 Teeth (Includes Ref. No. 14)
Position : 49
1 SPACER, 25/64 x 5/8 x 11/16
Position : 49
1 CAP
Position : 49
8 CAPSCREW, Hex Head, Whizlock, 1/4-20 x 5/8
Position : 50
1 BREATHER ASSEMBLY
Position : 50
4 * RING, Retaining, (Pkg. of 2)
Position : 50
1 CARRIAGE BOLT, 3/8-16 x 2-/1/4
Position : 50
8 NUT, Hex, Flange Lock, 1/4-20
Position : 51
1 BUSHING, Vent
Position : 51
1 * RING GEAR (43 Teeth)
Position : 51
5 WASHER, 5/16
Position : 52
1 UPPER HOUSING ASSEMBLY
Position : 52
2 * PINION, Bevel, (Includes Ref. No. 13)
Position : 52
1 SPACER (14 HP Models)
Position : 53
2 BEARING, Cradle
Position : 53
1 * PIN, Drive
Position : 53
2 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 (14 & 16 HP Models)
Position : 54
1 SWASHPLATE, Variable
Position : 54
1 BEARING, Thrust .30 x .52 x .13
Position : 55
1 * SPACER
Position : 55
1 GUIDE, Slot
Position : 56
1 ARM, Trunnion
Position : 57
1 * NUT, Lock, 5/16-24
Position : 57
1 * BRACKET, Brake Lever
Position : 58
1 * LEVER, Brake
Position : 60
1 * SPRING, Brake
Position : 61
2 * PIN, Dowel
Position : 62
1 * HOLDER, Brake Pad
Position : 63
1 * PLATE, Brake Pad
Position : 64
2 * PAD, Brake (Pkg. of 2)
Position : 65
1 * DISK, Brake
Position : 66
1 * STRIP, Bearing
Position : 67
2 * FITTING, Lubrication
Position : 69
1 * AXLE, (11-5/8" Long) (Includes Ref. No. 26, Qty. 2)
Position : 70
34" Mower Deck
Position : 1692546
Coronet, 11HP Gear 1692543 30" Mower Deck
Position : 1693303
Coronet, 13HP Hydro
Position : 1693305
Coronet, 14HP Hydro
Position : 1693307
Coronet, 11HP Gear (CE) 1692544 30" Mower Deck
Position : 1693309
Coronet, 13HP Hydro (CE)
Position : 1693311
Coronet, 14HP Hydro (CE)
Position : 1693313
411G, 11HP Gear 1694053 30" Mower Deck
Position : 1693315
413H, 14HP Hydro
Position : 1693317
2411G, 11HP Gear 1692545 34" Mower Deck
Position : 1693319
2414H, 14HP Hydro
Position : 1693321
2413H, 13HP Hydro
Position : 1693884
Coronet, 16HP Hydro
Position : 1694115
416H, 16HP Hydro
Position : 1694117
Coronet, 13HP Hydro
Position : 1694288
2413H, 13HP Hydro
Position : 1694289
413H, 13HP Hydro
Position : 1694290